Delta USB Devices Driver Download For Windows

05-15-2015, 09:42 AM (This post was last modified: 03-02-2018, 10:49 AM by steve.milici.)

Because of that we have found a solution to support those new drivers on our HMI’s. So if you have a new Windows 7 or Windows Vista and your drivers doesn’t works, don’t worry, and just follow the next steps: 1 – Check the firmware of your HMI. The first firmware version with the new Windows 7 drivers is V2.0170. USB Overdrive is a universal USB driver that handles all USB mice, trackballs, joysticks and gamepads from any manufacturer and lets you configure them either globally or on an application-specific basis. It reads all kinds of wheels, buttons.

Some users have experienced issues connecting their Turbo PMAC to a Windows 8.1 (and 10) system via USB, and instead seeing 'ACC54E USB' in Device Manager. If you experience this issue:
  1. Download the attached .zip file
  2. Extract the contents of it onto a USB Flashdrive connected to your computer
  3. Right click the 'ACC54E USB' in Device Manager and select 'Update Driver Software'
  4. Select 'Browse my computer for driver software' and select the flashdrive.

Delta Usb Devices Driver Download For Windows 8.1

WindowsWindows 8.1 should be able to see and properly load the drivers this way, and Device Manager should now show the PMAC under 'Motion Controllers'.
Attached Files
Windows 8.1 Drivers.zip (Size: 30.66 KB / Downloads: 448)

The CH340 chip is used by a number of Arduino compatible boards to provide USB connectivity, you may need to install a driver, don’t panic, it’s easier than falling off a log, and much less painful.


Windows

(Manufacturer’s Chinese Info Link)

  1. Download the Windows CH340 Driver
  2. Unzip the file
  3. Run the installer which you unzipped
  4. In the Arduino IDE when the CH340 is connected you will see a COM Port in the Tools > Serial Port menu, the COM number for your device may vary depending on your system.

Older Windows Driver Version and Instructions

  1. Download the Windows CH340 Driver
  2. Unzip the folder.
  3. If you are running a 64Bit Windows: – run the SETUP_64.EXE installer.
  4. If you are running a 32Bit Windows: – run the SETUP_32.EXE installer.
  5. If you don’t know, try the 64 bit and if it doesn’t work, the 32 bit.
  6. In the Arduino IDE when the CH340 is connected you will see a COM Port in the Tools > Serial Port menu, the COM number for your device may vary depending on your system.

Macintosh

(Manufacturer’s Chinese Info Link)

The following github has up to day pkg files for 1.3, 1.4 and 1.5 at time of writing, thanks to Joshua Wallis for bringing this to my attention…

Direct Download Links (from the github repo above):

Driver download for windows 10

See the github link above for installation instructions if you need them.

Windows 7 usb driver download

Previous macinstosh downloads if the above doesn’t work for you…

(V1.3) Download the CH340 Macintosh Signed Driver for Mavericks (10.9), Yosemite (10.10) and El Capitan (10.11) and Sierra (10.12)

Inside the zip file you will find a PDF and a “pkg” file, short version, double click the pkg file, the PDF has some extra information.

OSX Sierra (10.12) Note

A kindly user, Maarten Segers reports

FYI, the driver documented here WILL crash on OSX Sierra.

Delta Usb Devices Driver Download For Windows Usb

Make sure to use this one instead: https://github.com/MPParsley/ch340g-ch34g-ch34x-mac-os-x-driver

I can personally not test on MacOS and can not vouch for the above drivers at github, but there you go.

Delta Usb Devices Driver Download For Windows 10

See uninstalling information at the bottom of the page if the driver causes problems for you.

Here is an older version of the Mac driver, NOT FOR 10.12 Sierra

Delta Usb Devices Driver Download For Windows Operating System

(V1.0) Download the CH340 Macintosh Signed Driver for Mavericks (10.9), Yosemite (10.10) and El Capitan (10.11)

Linux

Delta Usb Devices Driver Download For Windows 7

(Manufacturer’s Chinese Info Link)

USB

Drivers are almost certainly built into your Linux kernel already and it will probably just work as soon as you plug it in. If not you can download the Linux CH340 Driver (but I’d recommend just upgrading your Linux install so that you get the “built in” one).

Uninstalling From Macinstosh

A couple of Mac users have said “the driver crashes my mac Sierra how do I uninstall”.

Firstly regards the crash make sure you installed the 1.3 version of the driver, not the old one. You could download it directly from the Manufacturers Website in case they have issued an update since I wrote this page.

Delta Usb Devices Driver Download For Windows Media Player

Secondly a quick google search reveals that this is how you uninstall:

  1. Open a terminal and type: cd /Library/Extensions/
  2. Verify that the .kext file is present: ls grep usbserial.kext
  3. Output should be: usbserial.kext
  4. Then type: sudo rm -R usbserial.kext
  5. Verify that the .kext file has been removed: ls grep usbserial.kext
  6. Output should be empty.
  7. After you should remove the files stored in receipts folder: cd /private/var/db/receipts/
  8. Find the enties: ls grep usbserial*
  9. Output should be: codebender.cc.ch34xinstaller.usbserial.pkg.bom codebender.cc.ch34xinstaller.usbserial.pkg.plist
  10. Remove each one of the files of the above list: sudo rm -r filename`